Your shopping cart is empty!
Your shopping cart is empty!
The ATM CES port adapter is a dual-wide module. It has four T1 (1.544 Mbps) or four E1 (2.048 Mbps) 120-ohm constant bit rate (CBR) ports that can support both structured (N x 64 kbps) and unstructured ATM Forum-compliant circuit emulation services (CES), and a single port of an OC-3 (155 Mbps) single-mode intermediate reach or a T3 (45 Mbps) or E3 (34 Mbps) standards-based ATM interface.The target application of the ATM CES port adapter is access to a broadband public or private ATM network where multis..
The ATM dual PHY OC-3 LANE/MPOA module (SMF),provides one direct connection and one standby connection between the 155-Mbps ATM network and the Catalyst 5000 family switch using two single-mode (SC) fiber-optic connectors.Spare Product, Reassembly of up to 255 buffers simultaneously; each buffer represents a packet, Support for up to 4096 virtual circuits, Support for ATM AAL 5, ATM LANE 1.0, including LEC, LES, BUS, and LECS, MPOA supportManufacturer: Cisco Systems, Inc Manufacturer Part Number: WS-X51..
The ATM interface processor (AIP) provides a single ATM network interface for Cisco 7000 series and Cisco 7500 series routers. The AIP provides a direct connection between the high-speed Cisco Extended Bus (CxBus and CyBus) and external ATM networks. A physical layer interface module (PLIM) on the AIP determines the type of ATM connection. There are no restrictions on slot locations or sequence; you can install an AIP in any available interface processor slot...
The ATM interface processor (AIP) provides a single ATM network interface for Cisco 7000 series and Cisco 7500 series routers. The AIP provides a direct connection between the high-speed Cisco Extended Bus (CxBus and CyBus) and external ATM networks. A physical layer interface module (PLIM) on the AIP determines the type of ATM connection. There are no restrictions on slot locations or sequence; you can install an AIP in any available interface processor slot...
The ATM OC-3c/STM-1 Network Module developed for the Cisco 3600 modular access routers provides a single-port SONET and SDH-based OC-3c/STM-1 interface for worldwide use. This module is designed to support the convergence of data, voice, and video services that allow customers to migrate existing voice and video traffic onto a corporate data network for substantial cost savings.1260 to 1360 nm Wavelength, Class A EMI, RFC 1483 support for multiple encapsulations over ATM, ATM PVCs and SVCs, Layer 2 per-VC..
The Cisco NM-1A-OC3-POM network module is a high performance single-width, single-port ATM network module, utilizing an optical carrier level 3 (OC-3) link. The ATM interface is a small form-factor pluggable (SFP) optical port. Fiber-optic cables to the network are attached to an SFP module that is inserted into the SFP port. The mode of operation is determined by the SFP module that is used.Supports 3 modes of operation: Multimode (MM). Single mode intermediate reach (SMIR). Single mode long reach (SMLR)..
The Catalyst 8510 MSR/LightStream1010 ATM Router Module (ARM) provides high-speed interworking between the Asynchronous Transfer Mode (ATM) and Layer 3 environment interfaces in a single chassis. The ARM is supported by the Catalyst 8510 MSR and LightStream 1010 platforms, providing large enterprises and service providers with a wide range of Layer 3 and ATM interfaces for building integrated solutions. The ARM can be used with the Catalyst 8510/LightStream 1010 ATM (T1 up to OC-12) and Layer 3 (Gigabit Eth..
This is compatible primarily with the Cisco LS1010 (Lightstream) and the 8500/8510 Series Equipment...
This is an ATM switch processor for the Cisco LightStream 1010 Switch -- comes with FC-Per-Class Queuing ( FC1 )The ATM Switch Processor (ASP) is a main system processor, which supports both the ATM switch fabric, together with its field-upgradable feature card, and the high-performance RISC processor, which provides the central intelligence for the device. The ASP module supports all of the cell-relay and signaling and management processing functionality of the switch. The ASP itself supports the 5-Gbps,..
Manufacturer: Cisco Systems, Inc Manufacturer Part Number: CAB-AC2AUS= Brand Name: Cisco Product Model: CAB-AC2AUS= Product Name: Standard Power Cord Product Type: Standard Power Cord Device Supported: Power Adapter Frequency: 50 Hz..
Manufacturer: Cisco Systems, Inc Manufacturer Part Number: ACS-2600ASYN= Brand Name: Cisco Product Name: Network Cable Package Type: Retail Product Type: Network Cable Connector on First End: 1 x RJ-45 Male Connector on Second End: 1 x RJ-45 Male Conductor: Copper..
Manufacturer: Cisco Systems, Inc Manufacturer Part Number: AXRJ48T3T1 Brand Name: Cisco Product Model: AXRJ48T3T1 Product Name: AXRJ48T3T1 Back Card Product Type: Service Module Application/Usage: Data Networking Interfaces/Ports: 8 x T1 WAN Interfaces/Ports: 1 x T3 WAN Interfaces/Ports Details: 8 x RJ-48 T1 WAN Interfaces/Ports Details: 1 x RJ-48 T3 WAN Data Transfer Rate: 1.54 Mbps T1 Data Transfer Rate: 44.74 Mbps T3 Compatibility: MGX 8200 AIMUY Trunking Module..
The Cisco MGX 8850 AXSM Enhanced (AXSM-E) ATM Switching Module is a high-density, double height service module for use in the Cisco MGX 8850 Multiservice Switch in combination with the high-capacity PXM-45 processor switching module. The AXSM Enhanced ATM Switching Module, in conjunction with the PXM-45, AXSM (Broadband ATM Switch Service Module), and Route Processor Module (RPM), offers the industry's most advanced and reliable ATM networking features, such as Private Network-Network Interface (PNNI), swit..