The single-port Cisco Gigabit Ethernet Network Module (part number NM-1GE) provides Gigabit Ethernet optical and copper connectivity for access routers. The module is supported by the Cisco 2691, Cisco 3660, Cisco 3725, and Cisco 3745 series routers. This network module has one gigabit interface converter (GBIC) slot to carry any standard copper or optical Cisco. The flexibility to use different GBICs allows for making a choice depending on various factors, such as distance, cost, existing infrastructure, f..
The single port Gigabit Ethernet Port Adapter (PA-GE) provides a Gigabit Ethernet connection for the Cisco 7200 and Cisco 7304 series routers. This port adapter (PA), which offers moderate performance, is suitable for campus, enterprise edge and wide-area network (WAN) aggregation applications. When used on the campus, the Cisco 7200 and Cisco 7304 series routers with the PA-GE connects the enterprise WAN to the Gigabit Ethernet campus backbone. At the enterprise edge, the PA-GE connects the WAN to the Giga..
Increasing demand for bandwidth-intensive services and wide-area network (WAN) connectivity requires that network administrators maximize the capacity and efficiency of network routers. Cisco Systems' High-Speed Serial Interface (HSSI) port adapters enables network administrators to leverage their investments in Cisco 7200, 7300, 7400, 7500 and 7600 Series Routers. This port adapter increases port density and enhances performance at the industry's lowest price per port.High reliability: Online Insertion a..
The HP ESCON PA is a high-speed port adapter that supports IP Datagram, TCP/IP Offload, TN3270 Server, TCP Assist, Cisco MultiPath Channel (CMPC), CMPC+, and Cisco SNA (CSNA) software applications. The HP ESCON PA provides a single channel interface for Cisco 7200-series routers. In some situations, this interface can eliminate the need for a separate front-end processor (FEP).128 MB of DRAM, Supported processor I/O architectures: ESA/390, Bit transmission: Serial, Channel data rate: Up to 17 MBps, Numbe..
Cisco 1-Port BRI (S/T) Interface Card, WIC-1B-S/T-V3The WIC-1B-S/T-V3 provides the ability to add BRI connectivity via a WIC, allowing administrators to maximize valuable slot space while providing additional connectivity options, such as Ethernet, on the same module.The WIC-1B-S/T-V3 inserts into a mixed-media network module or directly into the WIC slot on the following Cisco router series:1720, 1721, 1751, 1760
1900, 2900, 3900
Carrier modules, such as NM-1FE2..
The 1-port ISDN BRI S/T leased line WAN interface card (WIC) (WIC-1B-S/T-LL) is designed specifically for the Cisco 1603 R and 1604 R routers. It is intended for users who require a dialup ISDN BRI line (from the Cisco 1603 R or 1604 R router's built-in ISDN port) and an ISDN leased line (from this ISDN BRI leased line WIC inserted into the Cisco 1603 R or 1604 R router)...
To provide the real flexibility to its customers Cisco offers a variety of networking solutions. The Cisco routers feature network module slots, each of them accepts different network module interface cards, supporting a variety of LAN and WAN technologies. This ISDN BRI U WAN Interface Card provides your Cisco 1600, 2600, 3600 series routers with one ISDN BRI port (U interface, internal NT-1, RJ-45 connector). Note that this card does not support hot swap; however, no hardware damage will occur if it is sw..
The module has cPCI bus control circuitry that is used when it is installed in the top slot of the Cisco IPVC 3544 chassis. The module supports hot swapping when it is installed in chassis slots two, three, and four.Manufacturer: Cisco Systems, Inc
Manufacturer Part Number: IPVC-3540-MC03A=
Brand Name: Cisco
Product Model: IPVC-3540-MC03A
Product Name: IPVC-3540-MC03A 1-Port MCU Module
Product Type: Interface Module
Application/Usage: Data Networking
Interfaces/Ports: 1 x 10/100Base-TX
The PA-MC-E3 Multi-Channel E3 port adapter is available on Cisco 7200 series routers, on Cisco 7500 series routers, and on Cisco 7000 series routers with the 7000 Series Route Switch Processor (RSP7000) and 7000 Series Chassis Interface (RSP7000CI).The PA-MC-E3 has one channelized E3 high-speed serial interface that provides access to services at E1 (2.048 Mbps) data rates, transferring data bidirectionally. This port adapter divides the E3 signal stream into 16 E1 lines that can be further divided int..
This Cisco 1 Port Multichannel T3 Enchanced Capability Port Adaptor supports Cisco High-Level Data Link Control (HDLC), Frame Relay, PPP, and Switched Multimegabit Data Service (SMDS) Data Exchange Interface (DXI) encapsulations over the serial interface. This Port Adapter is designed to receive and transmit at the DSX-3 level while driving and receiving from 75-ohm coaxial cables (ATT 734A or equivalent quality coaxial cable). The T3 port connects directly to any equipment with DSX-3-level BNC connectors.
Cisco Multiflex Trunk Voice and WAN network interface module
NIM-2CE1T1-PRIThe CiscoÂ® Fourth-Generation 2-Port T1/E1 Multiflex Trunk Voice and WAN Network Interface Modules (NIMs) NIM-2CE1T1-PRI supportS data and voice applications on the Cisco 4000 Integrated Services Routers. These cards combine WAN-interface-card (WIC), voice-interface-card (VIC), ISDN Primary Rate Interface (PRI), dial-access integration, and channelized-data (CE1T1) functions to provide superior flexibility, versatility, and investm..
Basic T1/E1 data: The MFT versions act as WICs, supporting T1, fractional T1, E1, and fractional E1. To simplify remote management, these modules integrate a fully managed DSU/CSU for T1 deployments and a fully managed DSU for E1 deployments.E1/G.703 data: In addition to the basic T1/E1 data support, the CE1T1 versions also support structured G.703 with G.704 framing and unstructured E1 (G.703) applications.T1/E1 packet voice: All the modules support packet voice applications by providing T1, fractional..